Output 0 broadcast packets, 1 multicast packetsĬheck Controller Counters RP/0/RSP0/CPU0:ASR9001-F# show controllers tenGigE 0/0/1/1 stats Received 0 broadcast packets, 1 multicast packetsġ0001 packets output, 15140219 bytes, 0 total output drops Last clearing of "show interface" counters 00:00:32ĥ minute input rate 504000 bits/sec, 52 packets/secĥ minute output rate 504000 bits/sec, 52 packets/secġ0001 packets input, 15140219 bytes, 0 total input drops RP/0/RSP0/CPU0:ASR9001-F# clear countersĬlear "show interface" counters on all interfaces This clears counters on both the interface and controller. RP/0/RSP0/CPU0:ASR9001-F(config-if)# loopback external This test requires a length of fiber cable to physically loop the transmit (Tx) signals into the receive (Rx) port. This test verifies the linecard Central Processing Unit (CPU), fabric path, NP, transceiver, and optics.
Output good pkts = 10003 Output unicast pkts = 10000 Input good pkts = 10003 Input unicast pkts = 10000 Statistics for interface TenGigE0/0/1/1 (cached values): Output 0 broadcast packets, 3 multicast packetsĠ output errors, 0 underruns, 0 applique, 0 resetsĠ output buffer failures, 0 output buffers swapped outĬheck the Controller Counters RP/0/RSP0/CPU0:ASR9001-F# show controllers tenGigE 0/0/1/1 stats Received 0 broadcast packets, 3 multicast packetsĠ input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abortġ0003 packets output, 15140657 bytes, 0 total output drops
Last clearing of "show interface" counters 00:02:40ĥ minute input rate 685000 bits/sec, 126 packets/secĥ minute output rate 685000 bits/sec, 126 packets/secġ0003 packets input, 15140657 bytes, 0 total input dropsĠ drops for unrecognized upper-level protocol Output flow control is off, input flow control is off Hardware is TenGigE, address is 65 (bia 65) TenGigE0/0/1/1 is up, line protocol is up Success rate is 100 percent (10000/10000), round-trip min/avg/max = 1/1/5 msĬheck Interface Counters RP/0/RSP0/CPU0:ASR9001-F# show interfaces tenGigE 0/0/1/1 Pings with timeout=0 may result in system instability andĬontrol protocol flaps resulting in traffic impact.ĭO you really want to continue : y RP/0/RSP0/CPU0:ASR9001-F# clear counters tenGigE 0/0/1/1Ĭlear "show interface" counters on this interface RP/0/RSP0/CPU0:ASR9001-F(config-if)# end Clear Counters
RP/0/RSP0/CPU0:ASR9001-F(config-if)# loopback internal This is traffic impacting RP/0/RSP0/CPU0:ASR9001-F# configure It can find problems with the CPU, fabric path, NP and transceiver, but it cannot find optical or transit problems. This is a basic test that can be performed without access to a remote site. The below examples use this interface: RP/0/RSP0/CPU0:ASR9001-F# show run int tenGigE 0/0/1/1 Internal loops can be done remotely, but don't provide as much information.Įxternal loops must be performed at the site, but give the greatest amount of information. There are two primary kinds of loopbacks: internal and external. When necessary, loopbacks can be used to find problems with line cards, fabric, Network Processors (NPs), transceivers, or optical transit paths. Using Loopbacks to Test Ethernet Interfaces
0 kommentar(er)
